You can switch between the new Eco settings and a POWER setting, eg 7 WHILST DRIVING. (the actual Power setting is the one currently selected by the Synergy's rotary switch.)

Just change the setting and momentarily lift off the accelerator for the new setting to take effect. Previously, you had to restart the engine for the setting to change.

The dash switch requires a thin cable to be fed through from the engine compartment. Often there are unused blanking plugs / grommets or the cable can be fed through an existing one. Until the switch is connected, the module operates in the normal mode using the setting of the Synergy's rotary switch.

The dash switch can be located in any convenient place and attached with the supplied heavy duty velcro. Alternatively, you can replace the switch with a 2 or 3 way one (single pole) or a push-on push-off button (latching type - not momentary) and either not have the leds or fit low current ones else where. (must be low current type). Some OEM switches to match the others on your car's dash may be suitable - we can't supply these.

VEHICLES WITH DPFs. Urban or extra urban modes.

f you drive dpf / particulate equipped vehicle mainly on short urban journeys then you can use the off or eco setting in town and flick the switch when you need more power for overtaking or steep hills. Out of town you can use any setting. [ECO2 can be OFF if requested ].

TAXI drivers in particular are finding that vehicles with dpfs are a nightmare and our sister company does many dpf removals to solve the problem. However not all vehicles can have the dpf removed and if the vehicle is tuned, then a dash switch or push button gives the best of both worlds.

HIGH MILEAGE VEHICLES. Minimises strain.

 Some owners are concerned about tuning a high mileage vehicle. Normally this isn't a problem but for peace of mind, the Dash Switch is ideal. Just use the ECO setting for a mild increase and better economy, and switch to Power mode only when you need the extra oomph!

OTHER TUNING BOX SELLERS FORCE YOU TO CHOOSE BETWEEN A POWER OR AN ECONOMY VERSION.. NOT US!

You CAN have your cake & eat it. Use the ECO mode  - the equivalent of the 'green' boxes from other sellers, and then switch to POWER for performance more than equal to their red performance modules.

Simply put,  the dash switch enables the Synergy range to be the equal of two competitors products in one box for half the cost!

HIGH QUALITY CHROME LED PUSH BUTTON OPTION. An alternative to the 3position dash switch at extra cost.

We can supply a kit comprising a high quality chrome plated brass push on, push off switch with led in place of the switch shown above.

• ADJUSTABLE  BRIGHTNESS

• OUT  = ECO or OFF* IN = POWER

• PRE WIRED KIT - NO SOLDERING REQUIRED.

• SINGLE 16MM HOLE REQUIRED.

• LED SUPPLY IS  ISOLATED FROM THE SYNERGY.

• LED CONTROLLED BY THE SYNERGY  so you can see when the new setting engages.

• LED COLOUR OPTIONS: RED, GREEN OR BLUE.

• AVAILABLE WITHOUT PUSHBUTTON FOR USE WITH OEM SWITCHES

The push button switch kit. (appearance may vary)

Left to right:: Led power cable,  led adaptor & Synergy cable, & push button.

The harness is prewired ready to plug in once the push button has been installed.

The red/black wire connects to a 12v and gnd supply eg cig lighter or dash illumination. If this is varied by your car's dash rheostat, then the led will also dim. Current requirement is negligible (5-10ma)

The brightness adjusting screw is visible on the side of the led adaptor. Pre wired connectors - feed the cable from the pushbutton through the 16mm hole drilled in the dash or centre console and plug them onto the male ends, one 2pin, one 3pin so you can't mix them up.

USING AN OEM SWITCH OR PUSHBUTTON

Kit is available without the pushbutton so you can use any switch or push button of your choosing. (must be a latching type)

It can have an led built in or the led can be remote from the switch or push button.

The pushbutton wiring harness is supplied so this just needs connecting to the switch and led.

The 2pin connector is for the switch and the 3pin one for the led (2pins used, 1 spare)

It may even be possible to use the existing Sport button fitted to some Vauxhalls, or an auto gearbox Sport button.

INSTRUCTONS INCLUDED.

INTELLIGENT DESIGN FEATURES ENSURE RELIABLE SYNERGY OPERATION:

1. The pushbutton will control the Synergy mode even f the led supply is not connected or becomes disconnected. 

2. The 12volt LED supply is isolated from the Synergy by optical switches to prevent damaging battery voltage entering it in the unlikely event of a fault or short within the switch or led.

UPGRADE PATH FOR EXISTING SYNERGY OWNERS:               "you won't find any other make of tuning product as upgradeable"

In keeping with our policy of making our products upgradeable and transferable, you can return your Synergy 1 or 2 to have the new chip fitted and the '+' firmware installed. The costs are:-

If you already have a dash switch, you just buy the re-chip upgrade at: £15 + p&p

If you don't have a dash switch, then choose from the 3 position switch one or one of the chrome  red, green or blue led pushbuttons at £20 or £33 respectively. NB you have to buy both a switch AND the rechip upgrade so the total will be £35 or £48 + p&p

You can order these under Options in the Synergy 2 shop here:

You can even have a Synergy re cabled for a different vehicle, upgraded and a dash switch supplied. Total cost just £65 or £78 + p&p

"YOU'LL NEVER NEED TO BUY ANOTHER TUNING MODULE"

 Notes:

1. NOT AVAILABLE for some vehicles with Denso engine management.

2. For the Synergy 2a, 2b, both sections are changed by the dash switch.

PRICES: (postage not included)

3position toggle dash switch module: £20

Chrome led push button kit in place of 3 position switch: £33 (blue, green or red available)

Push button kit less the push button for use with your own switch and led. £15

Re-chip '+' upgrade for Synergy 1 or 2 - required for use with real time dash switch. £15

Re-cable where needed if you have changed vehicle : £30

* Please advise us if you want the 3pos dash switch centre position to be ECO2 or OFF, or with a push button, the 'out' position to be Eco 1 or OFF